A.B Sales

Correction Function:

• By point correction support single point, 2X2 points, 4X4 points and 8X8 point four correction mode, the biggest calibration 6144 points/module, red, green, blue each level of 256;By card (cabinet) used to display the between the correction of off color correction, red, green, blue each level of 256.

Intelligent identification card function:

• Intelligent identification procedures can identify double color, full color, virtual, lighting, etc all kinds of various drivers board scanning mode and various kinds of signal , recognition rate reached 99%.

65536 level (64 K) gray arbitrary setting function:

• According to the situation of display customers can arbitrarily set from no gray to level 65536 (64 K), make your screen to achieve the best display effect.

The refresh rate arbitrary setting, phase lock, synchronization function:

• set arbitrarily from 10 Hz refresh rate-3000 Hz, phase lock function to make the screen refresh lock the computer monitor refresh rate in integer times, put an end to the image rent, ensure perfect image reappearance. Phase lock synchronous range of 47 Hz-76 Hz.

Control area:

• Full color 4096(4K) gray level 180HZ refresh rate,max controls 512*128,twice than the sixth generation product,full color static 16384(16k)gray level 300HZ,max controls 160*64(note:need driving board can be on high 30MHZ clock)

Double cable heat backup function:

• The A and B two ports of receiving card can be used to input or output, can be used for two computers to control a screen at the same time, when one computer have problems, another one automatically replace it, also can be used for one computer with double cable control, when one cable have problems, another one automatically take it over, making the normal work of screen to get maximum security.

Many screens synchronization and composite function:

• Support a piece of sending card controlling pieces screens, the working state of screens can be arbitrary combination, synchronousdisplay, independent broadcasting, can be through the shortcut key, fast switching.

256 level automatically brightness adjustment:

• A level 256 automatic adjustment function make display brightness adjustment more effective.

Program online upgrade function:

• If the screen receiving card program needs to be upgraded, need to open display power and update through the LED studio, no need to detach receiving card from the display.

Break the traditional ideas without dial code switch:

• No dial code switch design, all Settings through the computer.

Test function:

• Receiving card integration test function, need not take send card can test display, slash, gray, red, green, blue, and the light, etc many types test mode.

Long distance transmission:

• Maximum transmission 170 meters (measured), ensure transmission 140 meters.

Supporting software:

• LED studio 10.0

• 10+ Bit Faroudja DCDI Cinema Processing
• New Faroudja Real Color
• Faroudja TureLife Video Enhancer
• Advanced 4×4 Pixels Interpolation Scaling Algorithm
• HDMI 1.3a with HDCP, HD 1080p input PAL/NTSC
• 10-bit Processing
• Seamless Switching, Fade-in / Fade-out switching & Blend switching in random input signals
• HD Text, Flash, Graphics & Logo Overlay
• 4 custom PIP / POP display modes, which can be switched by pressing one button
• Hot Spare function, display will be stable and reliable
• Picture Freeze function
• AIAO( Any In Any Out ) function allows for displaying any capturing picture in specific area on the scree
• 2048 x 1152 or 2304x 816 output for single machine
• Multi-machine in parallel, multi-unit installed in parallel drive indefinite LED lattice
• Easy setup and adjustment through knob and keys on the panel. Full design RS232 command for operating and setting
• Press keys or knob on frontal panel to directly select 10-channel input signal source,including:
• 2×CVBS 1×DVI 1×HDMI
• 1×VGA 1x USB
• 1×EXT.( extended modle , can be VIDEO or SD I / HD-SDI or VGA / DVI /HDMI )
• 2 channels can be configured to connect external stereo audio, plus DVI, HDMI and SDI audio, there are 5-channel audio for synchronous switch
• 2 LED Transmission Cards Built-in ability ( sending cards are optional )
• 24 / 7 Application

The ESP8266 NodeMCU CP2102 Board has a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all networking functions from another application processor.

• Open-source, Interactive, Programmable, Low cost, Simple, Smart, WI-FI enabled
• Arduino-like hardware IO
• Integrated TR switch, balun, LNA, power amplifier and matching network
• Integrated PLL, regulators, DCXO and power management units
• Onboard USB to serial chip to easily program and upload codes from the Arduino IDE
• Embeds logic level converter circuits
• Has onboard 3.3V regulator to ensure enough power to function as your go-to WiFi chip!
• Easy access to the GPIO pins for easy prototyping
• ESP-12E Processor
• Easy to use breadboard friendly form factor

Arduino Mega 2560 Board follows Open-source principles, which means you can freely download the development environment and many associated resources.

• Ideal for project work and often used in schools, teaching, motor control, robotics and similar applications; the Arduino platform allows for rapid application development using either Java (cross-platform) or Processing (a C derivative used to write sketches using Arduino IDE downloadable from Arduino.cc website.)
• Input voltage should be limited to 6 ~ 12V, but if the voltage supplied is less than 6V, I / O port may not be supplied to a voltage of 5V, and therefore readings may become unstable. If the voltage is greater than 12V, the regulator device may overheat causing damage to the control board. It is therefore recommended that you supply between 6.5 and 12V, utilizing typical power supplies of 7.5V or 9V.
• Mega 2560 is fully compatible with the Arduino software and has complete hardware compatibility with the Mega 2560 Arduino Shield high-performance processor and enough memory to handle even complex solutions.

This isCH340G USB To TTL Converter, USB to TTL / USB-TTL /STC microcontroller programmer / PL2303 in nine upgrades plate with a transparent cover Compatible with ARDUINO, RASPBERRY PI, AVR, PIC, 8051, etc.

• This USB – TTL converter is based on CH340G USB to Serial TTL converter chip. The module can be used for 3.3Volt logic level signals, the and has the option to switch from 5Volt to 3.3Volt logic level using a 2 pin shunt supplied with the module.
• The module includes a small switch which allows the voltage available at the VC (Supply output) pin to be switched between 3.3 and 5V. Data pins include TX, RX. These digital pins are at 5V TTL levels allowing them to be directly interfaced most 5V microcontrollers.

• Support WINDOWS 98 / ME / 2000 / XP / Server 2003 / VISTA /Server 2008 / Win7 / Win8 32 Bit / 64
• Support USB1.1 or USB2.0/USB3.0 for communication.
• Provide RS232, RS485, RS422 interface.
• Simulation interface, you can upgrade serial peripherals.
• Supports common MODE contact signal.
• Supports IRDA SIR infrared communication.
• Programming does not affect the target board program runs.